资源列表
danbaizhishuijie
- 温度传感器18B20汇编程序,采用器件默认的12位转化,最大转化时间750微秒 可以将检测到的温度直接显示到AT89C51开发实验板的两个数码管上 显示温度00到99度,很准确哦~~无需校正!-temperature sensor 18B20 assembler, using the default device into 12, the largest 750 microsecond conversion time can be detected by a direct indic
PIC16F877_code_1
- PIC16F877单片机运算子程序1.rar-PIC16F877 microcontroller Operational subroutine 1.rar
zl932
- 这是一个输入为0-75mV的直流电表程序，输出显示的最大量程为9999；具有报警和RS485通讯功能；-input 0-H13 DC Table procedures, the output of the largest range of 9999; with alarm and RS485 communication function;
glys31
- 这是一个根据输入信号计算功率因数的电表程序，具有报警和RS485通讯功能；选用电能IC为CS5460A,MCU为PHILIPS的LPC932芯片。-This is a calculation based on the input signal power factor meter procedures, with alarm and RS485 communication function; Energy use for the IC CS5460A, MCU for the LPC932 PH
12D_C51
- USB接口芯片pdiusbd12固件源程序-pdiusbd12 USB interface chip firmware source.
okstep
- 单片机步进电机实验，要安装keil_full和proteus 6.5sp5才可以运行（学单片机的应该懂，不用多说）-SCM stepper motor experiment, To install keil_full lic 6.5sp5 and can run (SCM should learn to understand , the answer)
hanzi2
- 单片机显示汉字实验，要安装keil_full和proteus 6.5sp5才可以运行（学单片机的应该懂，不用多说）-SCM showed Chinese experiment, To install keil_full lic 6.5sp5 and can run (SCM should learn to understand , the answer)
show-time
- 单片机并口实验，用于日历模拟，要考虑闰年和大月小月年月日并行运行，由于是模拟，设置每秒为一天。要安装keil_full和proteus 6.5sp5才可以运行（学单片机的应该懂，不用多说）-SCM parallel experiments, the calendar for the simulation, to consider a leap year and the date on the slow parallel operation, As the simulation is set up
c51A07
- 1.1概述 1.2 MCS-51单片机结构和原理 1.3 并行输入/输出口电路结构 1.4 时钟电路与复位电路-1.1 Overview 1.2 MCS-51 structure and principle 1.3 parallel input / output circuit node mouth conformation 1.4 clock circuit and reset circuit
sejishilu
- 本文从硬件和软件两方面介绍了MCS-51单片机温度控制系统的设计思路，对硬件原理图和程序框图作了简捷的描述。-paper from the hardware and software aspects of two MCS-51 temperature control system design, right hardware schematic diagram and the process was simple descr iption.
wendujiankongxitongdeseji
- 本设计系统包括温度传感器，A/D转换模块，输出控制模块，数据传输模块，温度显示模块和温度调节驱动电路六个部分。文中对每个部分功能、实现过程作了详细介绍。整个系统的核心是进行温度监控，完成了课题所有要求。 -the design system including temperature sensor, A / D converter module, the output control module, data transmission modules, Temperature Displ
zhinengfangdaowendukongzhixitongdeseji
- 本系统详细的描述了智能防盗系统的基本原理 组成 对电话网络的接入方法进行了详细的描述-the system detailed descr iption of intelligent detection system composed of the basic tenets of the telephone network access methods for details detailed descr iptions