资源列表
AD7606_103ZE_FSMC__DMA_USB_FIFO_8CH_200KHz
- 通过stm32f103z，控制AD7606实现数据采集，将采集到的数据通过芯片FT2232，以USB总线快速传输，共8个通道，可同时达到16位，200k的采样率。(Through stm32f103z, AD7606 is controlled to realize data acquisition, and the collected data is transmitted quickly through chip FT2232 to USB bus. There are 8 channels
CAN-1
- 基于STM32F4例程,CAN总线的编程方式，开发语言是C语言.........(Based on the STM32F4 routine, the programming mode of the CAN bus, the development language is the C language.)
白光烙铁_V3.2.0不带时钟
- OLED屏烙铁源代码，已通过KEIL编译通过(OLED soldering iron source code, compiled through KEIL)
led测试程序（调试通过）
- led测试程序，led灯基础点亮！stm32(LED test program, LED light foundation lighting! Stm32)
adc2
- stm32 adc 测试，自己测试能用。非常实用（标准库）(Stm32 adc test, own test can be used. Very practical (standard library))
src
- MSP430实现RS485通信，LCD显示，已经相关业务实现。(MSP430 implementation of RS485 communication)
MSP430F5529-UART-RTC
- RTC+UART,可以通过串口发命令控制是否发送时间以及发送的间隔时间(RTC,UARTC,commands can be sent through the serial port to control whether to send the time and send the interval)
P1_PLUS_V2.0
- stm8L052应用例程，驱动12864液晶及LED显示，是初学者很好的参考资料。(Stm8L052 application routine, driving 12864 LCD and LED display, is a good reference for beginners.)
wenShiDu
- 用于GEC210板子的DTH11温湿度传感器驱动(DTH11 temperature and humidity sensor driver for GEC210 board)
ADC0832应用
- 基于AT89C51，采用LCD1602液晶显示0~5V模拟电压量。采用proteus仿真和KEIL4 C语言编程实现。(Based on AT89C51, the LCD1602 liquid crystal display 0~5V is used to simulate the voltage quantity. It is realized by Proteus simulation and KEIL4 C language programming.)
数码管显示温度
- 温度传感器（temperature transducer）是指能感受温度并转换成可用输出信号的传感器。温度传感器是温度测量仪表的核心部分，品种繁多。按测量方式可分为接触式和非接触式两大类，按照传感器材料及电子元件特性分为热电阻和热电偶两类。(A temperature sensor is a sensor that can sense the temperature and change it to a usable output signal. Temperature sensor is t
8、交通灯
- 绿灯亮时，准许车辆通行，黄灯闪烁时，已越过停止线的车辆可以继续通行；没有通过的应该减速慢行到停车线前停止并等待，红灯亮时，禁止车辆通行。给行人看的叫人行横道灯，通常指由红、绿（绿为蓝绿）二种颜色灯组成用来指挥交通通行的信号灯，红灯停，绿灯行。(When the green light is on, the vehicle is allowed to pass. When the yellow light is flashing, the vehicles that have crossed th