资源列表
main
- this the source code for Pulse width modulation LED shading-this is the source code for Pulse width modulation LED shading
tcp_socket_camera
- cc3200实现MT9D111摄像头的数据传输到android手机端-Cc3200 u5B9E u73B0MT9D111 u6444 u50CF u5934 u7684 u6570 u636E u4F20 u8F93 u5230android u624B u673A u7AEF
Altera-SOC-FPGA
- 讲述了Alteral公司SoC FPGA的几个应用实例- U8BB2 u8FF0 u4E86Alteral u516C u53F8SoC FPGA u7684 u51E0 u4E2A u5E94 u7528 u5B9E u4F8B
analog-high-pass-filter
- Design and analysis of active analog high pass filter -Design and analysis of active analog high pass filterDesign and analysis of active analog high pass filter
Temperature_Alarm
- 基于51单片机和C语言的温度报警器的设计，可手动设置温度- U57FA u5351 u5355 u7247 u7A8 u7B3 u7B0
zephyr_thread
- threads, semaphore and interrupt application on zephyr，按下按键后能够区分长按或者短按，并通过semaphore让相应thread得以继续运行，通过串口和LED显示长按和短按结果-threads, semaphore and interrupt application on zephyr, the application can recognize hold and short press, the uart and led will sho
zephyr_sensor
- 基于Zephyr v1.7.0开发的MPU6050 sensor读取程序，MPU6050的驱动位置zephyr目录zephyr-v1.7.0/drivers/sensor/mpu6050-MPU6050 sensor application base on Zephyr v1.7.0, the MPU6050 driver is under zephyr-v1.7.0/drivers/sensor/mpu6050
FLASH_WRITE_of_MSP430
- This program first erases flash seg C, then it increments all values in seg C, then it erases seg D, then copies seg C to seg D. Seg C @ 1040h Seg D @ 1000h The EEI bit is set for the Flash Erase Cycles. This does allow the Timer_A Interrupt
UART_of_MSP430F249
- Echo a received character, RX ISR used. Normal mode is LPM0. USCI_A0 RX interrupt triggers TX Echo. Baud rate divider with 1MHz = 1MHz/19200 = ~52.1 ACLK = n/a, MCLK = SMCLK = CALxxx_1MHZ = 1MHz
SPI_of_MSP430F249
- SPI master talks to SPI slave using 3-wire mode. Incrementing data is sent by the master starting at 0x01. Received data is expected to be same as the previous transmission TXData = RXData-1. USCI RX ISR is used to handle communication with
I2C_of_MSP430F249
- This demo connects two MSP430 s via the I2C bus. The master reads 5 bytes the slave. This is the MASTER CODE. The data the slave transmitter begins at 0 and increments with each transfer. The USCI_B0 RX interrupt is used to know when new data h
TimerA_of_MSPF249
- Toggle P1.0 using software and the TA_0 ISR. Timer_A is configured for up mode, thus the timer overflows when TAR counts to CCR0. In this example, CCR0 is loaded with 1000-1. ACLK = TACLK = INCLK = 32768Hz, MCLK = SMCLK = default DCO ~1.045Mhz