资源列表
hdcopy
- 硬盘克隆软件。可以将硬盘上所有数据（甚至隐藏分区上的数据）原封不动不动地复制到其它硬盘上，目的硬盘最多三个。-drive cloning software. It will drive all the data (or even the hidden data) Fixed intact copied to other drives, hard drives up to three purposes.
hextoasc-time
- 是一个将16进制转为ASC显示的程序，它是显示了系统当前时间的小程序，但是并不能实现时时显示当前程序，只是为了学习进制转换而写的。 有谁能够改进一点，请教教我。 QQ:254082939-is a band of 16 to show that the ASC procedures, it is an indication that the current time of the system of small procedures, but that will not always s
disp
- 一个用FASM写的显示彩条的程序。 可是我还不会用它显示字符呢。有谁会呢？请教教我啊。 QQ：254082939-FASM write with a display of the color process. However, I will not use it to display character?. Who will? Consult taught me ah. QQ : 254082939
F200asm
- IC卡底层操作接口,符合正向约定和反向约定.-bottom IC card interface, agreed with forward and reverse agreement.
LED_display
- 汇编编写的S52单片机控制的LED数码管灯显示2位16进制程序-compilation prepared by the S52 MCU control of the LED digital display of lights two 16-band procedures
2005微计算机技术
- 这是我们老师的PPT 事关于计算机接口的 是我们学校公认的高质量的课件 实为教学和学习的最好的参考-This our teacher's PPT things on the computer interface is our school recognized the quality of the real courseware for teaching and learning of the best reference!
xpm3
- 该文件的内容是设计一个五层楼的电梯控制装置,要求每层楼根据需要控制设上下控制按键及按键指示灯,全部楼层只设置一个当前楼层显示 电梯内设开关门按键 各楼层按键及指示灯,开关门要有声响提示 每层楼高度为0.30米,楼层全高1.5米-the contents of this document is to design a five-storey building in the lift control device on each floor under the requirements necess
as
- 一个很好的读写硬盘主引导区的程序. 适合于改进后做一键还原及BOOTMANAGER 等软件. -a good master boot drives to read and write the procedures. Suitable for improvement after doing a bond reduction and BOOTMANAGER software.
voicecontrol
- 语音电压表。 // 文件来源：《SPCE061A单片机实验指导书》,\"实验三十八 0~3V电压测量表\"-voice voltage meter. / / Source of the document : "SPCE061A experimental guide book", "Experiment 38 0 ~ 3V voltage measurement table"
kl10键盘显示
- 这是一个键盘显示的程序,一般键盘都可以用它,只是需要你更改其中的一些参数而已,很不错吧!-This is a keyboard and display procedures, the general keyboard can use it, you only need to change these parameters only, very good!
200hz频率产生
- 此程序完成功200HZ的固定频率,稳定性很高,波形失真度小,如果要想产生固定频率,这个程序是最好的选择!-success of this procedure 200Hz End of fixed-frequency, high stability, waveform distortion small, if they have a fixed-frequency, the procedure is the best choice!
顺序脉冲波
- 这个程序真的很有用,它可以告诉你怎样来运用单片机,不仅仅是写一个程序而已,相信你看了之后一定收获不小!-this procedure is really useful, it can tell you how to use the microcontroller, is not just a procedure adopted, I believe you will certainly learned a lot after reading!