资源列表
Login-interface-design
- 给大家上传一个利用选项卡做的登录界面，当关闭退出页面时自动清除登录名和设定密码，大家如需可直接套用。-For everyone to upload a tab to make use of the login screen when closed exit pages automatically clear the login name and password is set, you can directly apply additional.
I_V
- its an example program for IV measurement with keithley 2612A
111
- tcpIP协议在labview中的应用,本程序进行了简单的编程，实现了自发自收-tcpIP protocol in labview in the program for a simple programming, the spontaneous self-closing
115
- 串口的调试程序，实现数据的发送和接收内容的显示，类似串口调试器-Serial debugger, sending and receiving content data show similar serial debugger
Greenhouse-monitoring-system
- 温室监控上位机程序，基于LABVIEW编写的，包括温度和湿度数据采集程序、信号处理和显示等部分。已调试成功。-Greenhouse monitoring host computer program, based on LABVIEW prepared, including temperature and humidity data acquisition program, signal processing and display part. Has been successful commis
MAX2
- C语言编写的求两个数中的最大值，求解方法为采用第三变量求解-C language seeking the maximum of two numbers, solving method to solve for the introduction of a third variable
mnwdcjxt
- 模拟温度采集系统：有华氏和摄氏两种显示模式；可设定温度上限（摄氏），当温度超限时，Alarm Counter加1；当用户单击“开始采集”按钮后，系统开始采集数据；采集过程中若单击“暂停”按钮则弹出对话框停止采集，关闭对话框则在原有基础上继续采集。采集点数为100，在数据采集完毕后停止系统或者单击“停止系统”按钮停止系统。采集进度由进度条显示。-Analog temperature acquisition system: There are two kinds of Celsius and Fah
llzqx
- 洛伦兹曲线：生成一条三维的洛仑兹曲线，独具美感。-Lorenz curve: generate a three-dimensional Lorentz curves, unique beauty.
zxbfzxhfsq
- 正弦波仿真信号发生器：可生成可调幅值、频率、相位、直流偏移量的正弦波仿真信号。-Sine wave signal generator simulation: generate adjustable amplitude, frequency, phase, dc offset sine wave signal simulation.
xuexizaji1
- LabVIEW高手学习笔记：很好的LabVIEW学习笔记，很难找，这是第一卷。-LabVIEW expert study notes: good LabVIEW study notes, it is difficult to find, this is the first volume.
xuexibiji2
- LabVIEW高手学习笔记：很好的LabVIEW学习笔记，很难找，这是第二卷。-LabVIEW expert study notes: good LabVIEW study notes, it is difficult to find, this is the second volume.
LABVIEW
- 在前面板中放置3个LED灯，当程序运行后第1个LED打开并保持3秒，然后关闭，同时打开第2个LED并保持5秒后关闭，同时打开第1个和第3个LED保持5秒后，程序停止。-Place the three front panel LED lights, when the program runs the first one LED open and hold for 3 seconds, then turn off, while the first two LED open and hold for