搜索资源列表
FLUEPROG
- 一个流量控制仪器的源码，p89c668单片机，继电器输出／LED输出／can总线／智能卡／rtc等-a flow control device of the source code, p89c668 microcontroller, Relay output / output LED / can Bus / smart card / rtc etc.
risc_8051_v
- 流片过的risc_8051源代码 verilog语言描述的~-flow unit off risc_8051 verilog language source code described in the ~
test05
- UART RX with simple logic flow to check the protocol correct or not. Important is that the logic flow.
rs232
- RS232.C was written to provide all of the basic functionality needed to employ serial I/O in any application written with Borland C language compilers. Some features are: 1. Ease of use. No assembly language or library files are use
闸流管和双向可控硅成功应用的十条黄金规则
- 闸流管和双向可控硅成功应用的十条黄金规则，推荐下载。-gate and the two-way flow for successful application of SCR 10 gold rules, recommended download.
zhiling.rar
- 复杂模型机设计(内附:微指令设计,微程序,流程图,模型机设计报告,测试程序,验证程序)是本人复杂模型机设计的全部成果,The complexity of model design (with: microinstruction design, micro-process, flow chart, the report model design, testing procedures, the verification process) is a complex model, I design a
EasyARM1138UART
- 本例是easyarm1138的UART(通用异步收发器)实例 建议采用Windows自带的“超级终端”来调试UART， 在“端口设置”里，设置如下 波特率：9600 数据位：8 奇偶校验：无 停止位：1 数据流控制：无 -This case is easyarm1138 the UART (Universal Asynchronous Receiver Transmitter) proposed to u
BaselineJPEGSoftwareCodecCodes
- In term project, we will take the baseline JPEG codec in ARM-based platform system as an example to practice the design flow in SoC. We divide the project into three parts, and the goal of each part is described as follow. Part I: Design a baseli
ARM_developmnet_manual
- ARM工程师开发入门宝典，介绍了ARM嵌入式系统的开发流程-This is an abecedarium for ARM developers. It introduce the development flow of ARM embedded system.
20081004uu
- 利用easyARM2200的UART口接收从PC机过来的客流发生数据-EasyARM2200 I use the UART to receive back from the PC-flow data happen
Arm_Process
- ARM开发的流程说明，帮助你对ARM开发中间遇到的一些问题作为一种很好的诠释-ARM development of flow that you assist the development of ARM between some of the problems encountered as a very good interpretation
No.1
- 周立工easy_arm多媒体课件，共分有8章，里面详细介绍了，ARM开发的流程，并配合原理图有重点的分析，对ARM初学者有很强的帮助-Zhou workers easy_arm multimedia courseware, there is divided into 8 chapters, which described in detail, ARM developed flow, and in line with the principle diagram of the analysis ha
No.2
- 周立工easy_arm多媒体课件，共分有8章，里面详细介绍了，ARM开发的流程，并配合原理图有重点的分析，对ARM初学者有很强的帮助-Zhou workers easy_arm multimedia courseware, there is divided into 8 chapters, which described in detail, ARM developed flow, and in line with the principle diagram of the analysis ha
No.3
- 周立工easy_arm多媒体课件，共分有8章，里面详细介绍了，ARM开发的流程，并配合原理图有重点的分析，对ARM初学者有很强的帮助-Zhou workers easy_arm multimedia courseware, there is divided into 8 chapters, which described in detail, ARM developed flow, and in line with the principle diagram of the analysis ha
No.4
- 周立工easy_arm多媒体课件，共分有8章，里面详细介绍了，ARM开发的流程，并配合原理图有重点的分析，对ARM初学者有很强的帮助-Zhou workers easy_arm multimedia courseware, there is divided into 8 chapters, which described in detail, ARM developed flow, and in line with the principle diagram of the analysis ha
2410wanquankaifaliuchengjiyuanma
- 2410完全开发流程及源码，一些裸板的2410源码，帮助你学习bootloader，vivi的基本原理，认识中断以及MMU-2410 fully developed flow and the source, some bare-board source of 2410 to help you study bootloader, vivi the basic principles of interruption, as well as MMU Know
TMS320C671x
- 图解TMS320C671x烧写流程,看图就知道哦.-TMS320C671x flow diagram programmer, read on to know, oh.
FLOW
- /* 流量程序第1版 Finish Date: 2011\2\21 改动日期：2011\7\15 版本号：U1.0 采用11.0592MHz外部晶振 显示方式：动态扫描 功能描述: 1.检测流量，单位1m3/min=60m3/h 2.检测范围，0~100m3/min 3.频率输出200-1000Hz 调试方法：0 调零，1 量程，2 线性，3 报警点，4 断电点，5 复电点，6 自检点，7 自检， 8 AD输入电压，9 灵敏
flow
- 气体流量标准控制装置的控制系统下位机控制程序-Gas Flow Standard Equipment
flow
- 实现气体流量标准装置的控制,采用msp430f149单片机实现，-Gas Flow Standard Equipment