搜索资源列表
PDrunLjx
- 对多个中断的相互运用，独立互不冲突 在掉电状态，允许外部中断0,外部中断1,外部中断2唤醒。arm7,lpc2104周立功开发板 -interruption of a number of the mutual use of each other independent of the power-down mode of the conflict, allowing external interrupt 0, an external interrupt, external interrupt
arm8019
- 开发工具用EMBEST IDE进行开发,该程序是一个S3C44B0直接驱动网卡的程序,包括8019初始化,物理层收包发包,UDP的接收和发送,IP的发送和接收.已及ARM的地址解板,整个程序是自顶而下,方便进行网卡研究用,也可将其移植到8051单片机上使用-development tools used EMBEST IDE for development, the program is a direct drive S3C44B0 card procedures, including 8019
PhiARM
- philips的ARM芯片资料，很NB的，比NBA都NB，不错，你下来-Philips ARM chip, the very NB, NB NBA, it is true that you see down
2972
- C51单片机驱动a3972步进电机细分，同时可以控制步电机加速，减速-C51 single-chip stepper motor driver a3972 broken down step-by-step motor can be controlled simultaneously to speed up, slow down
CC2530_test
- CC2530的实验例程代码，打包好了，不用一个一个下载-CC2530 experimental sample code, packaged well, not one by one down!
demo
- Flex chip implementation File: UP2FLEX JTAG jumper settings: down, down, up, up Input: Reset - FLEX_PB1 Input n - FLEX_SW switches 1 to 8 Output: Countdown - two 7-segment LEDs. Done light - decimal point on Digit1. Operati
2440Board_Test_Source
- 一个2440开发板的测试源码，学习ARM9的可用下来-A 2440 development board test source, the study can be used down to see ARM9
7026_Temperature_measurent
- Power down mode arm mcu aduc7026 for supply
LCDDemo(lcd_led_buttom)
- STM32F10xx的LCD驱动源码，还好啦，需要的可以下下来看看的哦。-The LCD driver STM32F10xx source, but also Well, need to take a look at the oh down under.
STCPS2
- 51光电编码器实现，STC处理编码器的要求，同时编码根据PS/2协议，实现上下键以及确定键。-Optical encoder 51 to achieve, STC encoder processing requirements, as well as coding in accordance with PS/2 protocol, to achieve and to identify the key up and down keys.
AutoShutDo1721923192004
- This app will auto shut down your win xp computer by setting the time.
motordriver
- 用串口发命令驱动步进电机，使其正传反转，加速减速-Made by serial command-driven stepper motor to The True Story of reverse, speed up slow down
2440_NAND_ROOT
- 基于MINI2440的NAND启动代码，将起始地址设为0，下到NAND就行了。由于启动代码中会进行sdram的清0，nand的复制，启动过程大概要等5，6秒-MINI2440 of NAND-based startup code, the start address set to 0, down to the NAND on the list. As the startup code will be conducting sdram Qing 0, nand a copy, the boot p
arm_architecture_reference_manual_errata_markup_3_
- ARM v7_AR 体系结构手册，2008年的最新版本。好不容易下到了，给大家分享。-ARM v7_AR architecture manual, 2008, the latest version. Finally down to, and for everyone to share.
down-mb90092
- AVR驱动MB90092, 中英文双语显示-AVR驱动MB90092 中英文双语显示
51_sl811-u-rw.c
- 用51读写U盘的51程序，KEIL编译器，有用的朋友下来看看。-U disk with 51 to read and write 51 programs, KEIL compiler, useful friend came down to see.
GPIO_RVMDK
- 本源码为STM32的GPIO使用例程,主要演示GPIO的使用。开发环境realviewMDK。 程序通过按键对应的引脚的电平是否被拉低来判断按键是否被按下，如果按键被按下，则相应的LED闪烁一次。-The source code for the STM32' s GPIO use of routine, the main demonstration GPIO use. Development environment realviewMDK. Program through the bu
dianjikongzhi
- 利用c语言描述的步进电机加减速控制程序，实现电机的加速至匀速运动，运行一段时间后减速至停止。 -Using c language to describe the acceleration and deceleration of the stepper motor control program to realize the motor to accelerate to the uniform motion, run a period of time to slow down to stop.
CHxx_IROM_ApplicationNote_Rev1.00_080801
- s3c6410x的irom的说明(application Note)，v1版本。在6410的手册里面压根没讲！ 找了好久了，在csdn上下的，害得我最后一个积分也弄没了！只要大家能用上就值了！-s3c6410x of irom note (application Note), v1 version. Which are fundamentally in the 6410 manual did not talk about! Looking for a long time, and in th
stm8s103-UP-down-eadge-triggle
- STM8 定时器1 脉冲捕捉 ,上下沿都捕获 PC1输入 IAR1.2平台-STM8 timer1 pulse capture both up and down eadge PC1 input for IAR1.2 or later