搜索资源列表
lpc2148_usbaudio
- LPC2148 USB Audio Device Example This USB example project implements an USB Audio Device that connects via the USB interface to the PC. It may be used on the following devices: LPC2141 LPC2142 LPC2144 LPC2146 LPC2148 An USB Audi
S3C2410_BIOS
- 第一版YL2410开发板的BIOS 功能比较简单，上电之后，LCD显示蓝色、绿色、红色三个竖条 同时串口显示如下： Power on reset ************************************ * * * YL2410 Board BIOS V2006 * * Http://www.ucdragon.com * * * ************************************ NAND Flash Bo
LPC1114_IAP_update
- 实现LPC1114的在线升级功能，通过uart更新功能函数-LPC1114 achieve the online upgrade function, update function via the serial port function
boot_eth
- LM8962通过bootloader的以太网接口在线更新应用程序，克根据用户的需要将其修改成串口、SSI、USB等其他接口方式-LM8962 Ethernet interface via the bootloader update the application online, g according to the user' s need to change it into a serial port, SSI, USB and other interface mode
STM32_USBSD
- 基于STM32的，通过USB读SD卡程序。相当制作了一个SD读卡器。内有USB及SD卡读写程序等。完整工程。keil MDK3.22A以上打开-Based on the STM32, the SD card via USB reading program. Rather produced a SD card reader. There are USB and SD card reading and writing procedures. Complete works. keil MDK3.22A
oled
- The same program for SEPS525 chip set .. This code interface with OLED SEPS525 via SPI (Micro wire) interface of OMAP 5912 The code make the OLED ON, but sill not able write to the display
sci_rcv
- 利用PIC16F877A单片机,通过串口控制PWM占空比实现PWM输出程序-PIC16F877A MCU via the serial port to control the PWM duty cycle of PWM output program
dcc
- 调试通道例子。DCC is available on ARM cores which contain EmbeddedICE logic, e.g. ARM7TDMI, ARM9TDMI, etc. DCC is accessed by the target via coprocessor 14 using the ARM instructions MCR and MRC. The two assembler source files provided are: out
ARM2410
- 实现查询方式串口的收发功能。接收来自串口（通过超级终端）的字符并将接收到的 字符发送到超级终端-Implementation of the transceiver serial port query functions. Receive from the serial port (via HyperTerminal) characters and will receive the characters sent to HyperTerminal
ARM
- 摘 要：本 文 介 绍 了 一 种 以 LPC2210微 处 理 器 为 主 控 制 器 ，以 ~C／OS—I1为 嵌 入 式 操 作 系 统 的 嵌 入 式 信 息 家 电远 程 控 制 系 统 ．通 过 互 联 网 实现 对 家 用 电 器 的远 程 智 能 控 制 。 该 系统 实 用，功 能 灵 活 多 样 ，可 以 对 被 遥 控 对 象 的 状 态进 行 查 询 以 及 控 制 ，可 以 广 泛 地 应 用 于 家 用 电 器 或 者 其 他 场 所 的 各 种
STM32P103VBT6_with_dfu_full
- STM32 DFU FULL(V3.0.1) You can upload your program via USB-DeviceFirmwareUpdate mode
STM32P103VBT6_with_mass
- STM32 MassStorageClass Sample with shimple buffers you can acceess via SDCARD via spi interface
Addition_multiplication
- This MIPS program performs addition and multiplication operations for any two input numbers with fraction, via differentiating left and right hand sides and performing the specified operation.
ads7870
- /// The basic specs of the ADS7870 are: /// - Fast SPI interface (up to 20MHz) /// - 12-bit results /// - 8 single-ended or 4 differential input channels /// - Programmable gain stage (1,2,4,5,8,10,16,20x gains) /// - Software or
usb_lcd
- A simple V-USB data communication example, intend to display the messages transfered by PC via USB port on a text LCD with a ATmega8. AVR firmware is built with WinAVR GCC and software is built with BC++B5.
an2659
- stm8 bootloader, IAP program via uart program data into eeprom-stm8 bootloader,stm8 bootloader, IAP program via uart program data into eeprom
I2C
- arm7\EasyARM1138例程，I2C(互联IC总线)-arm7 \ EasyARM1138 routines, I2C (via IC Bus)
EXAM01
- You may control P0, P1, P2, P3 by using simple instruction A , B , C , D + [control byte}, at 57600bps with 22.1184MHz osc.-Programmable digital IO controller for c51 via RS-232 interface.
ADC
- STM32F103VBT6开发板上的ADC程序，通过定时器定时，将转换的数据通过串口传到PC机上-STM32F103VBT6 development board' s ADC program, the timer time, the conversion of data transmitted via the serial port on a PC,
sd_card
- SD card using FAT file system This example application demonstrates reading a file system from an SD card. It makes use of FatFs, a FAT file system driver. It provides a simple command console via a serial port for issuing commands to view and naviga