搜索资源列表
uboot_nios
- Nios II的uboot bootloader程序，完全可以在Nios SDK Shell下编译。-Nios II uboot Bootloader procedures, can the Nios SDK Shell compiler.
cdk4nios-0.3
- nios-linux交叉编译器,可以在linux环境下建立nios的交叉编译环境.-nios - linux cross-compiler, linux environment can be established under nios cross-compiler environment.
uClinuxforNiosII
- 运用 uClinux for Nios II开发环境创建-use for Nios II uClinux development environment created
mailbox.rar
- niosII多核之间mailbox在UCLINUX下使用的驱动程序,drivers for maibox under uclinux ,by which nios can communicate with each other
nios2gcc
- 一个uClinux gcc for nios_ii的交叉编译器.-a uClinux for nios_ii gcc cross-compiler.
uclinux.vga.driver
- nios上的uClinux环境下的VGA驱动-Nios uClinux on the circumstances of VGA driver
neek_alternate_sd_card_controller
- This SPI-mode SD Card controller is a free SOPC Builder component that can be used in any SOPC Builder system. The included example design runs on the Nios II Embedded Evaluation Kit, Cyclone III edition (NEEK).-This SPI-mode SD Card controller is a
nios2gcc
- 当我们想将uClinux移植到NiosII上时，需要在Linux上安裝Nios II gcc cross compiler。下载后请用RAR解压，然后方可在Linux下解压安装-When we want to migrate to NiosII on uClinux, the need to install Linux on the Nios II gcc cross compiler. Please download RAR decompression, and then only in ex
u-boot--1.1.4
- u-boot 1.14板源码，是遵循GPL条款的开放源码项目。从FADSROM、8xxROM、PPCBOOT逐步发展演化而来。其源码目录、编译形式与Linux内核很相似。除了支持PowerPC系列的处理器外，还能支持MIPS、 x86、ARM、NIOS、XScale等诸多常用系列的处理器-u-boot 1.14 board source, is to follow the terms of the GPL open source projects. From FADSROM, 8xxROM, P
linux-nios
- 嵌入fpga内的niosii，uClinux的sopc软件，很有用-sopc uClinux
FFT
- 基于Altera Cyclone II 系列FPGA嵌入高性能的嵌入式IP核(Nios)处理器软核,实现了基于FFT的音频信号分析-Altera Cyclone II FPGA family based embedded high-performance embedded IP core (Nios) soft core processor to achieve a FFT-based audio signal analysis
4CE6_ADC
- 关于AD转换的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for AD conversion，debugging on EL-ARM-DSP-IV experiment box.
4CE6_DAC
- 关于DA转换的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for DA conversion，debugging on EL-ARM-DSP-IV experiment box.
4CE6_DCMOTOR
- 关于直流电机的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for DC motor，debugging on EL-ARM-DSP-IV experiment box.
4CE6_UCOS
- 关于UCOS的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for UCOS，debugging on EL-ARM-DSP-IV experiment box.
4CE6_STEPMOTOR
- 关于步进电机的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for step motor，debugging on EL-ARM-DSP-IV experiment box.
4CE6_IIC_CARD
- 关于II card转换的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for II card，debugging on EL-ARM-DSP-IV experiment box.
4CE6_HD7279
- NIOS按键源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for key，debugging on EL-ARM-DSP-IV experiment box.
4CE6_leddot
- NIOS跑马灯源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for LED，debugging on EL-ARM-DSP-IV experiment box.
4CE6_RS232
- 关于RS232的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for RS232，debugging on EL-ARM-DSP-IV experiment box.