搜索资源列表
3线双向零等待IO通讯机制
- 3线双向零等待IO通讯机制 单片机通讯源代码带说明-3 bidirectional zero waited for the IO communication machine-made monolithic integrated circuit communication source code belt explained
chexu
- PWM 码是一种脉宽调制码，它的组成为9MS 高电 平和4MS 低电平引导脉冲，16 位系统识别码 正码和8 位数据反码。我们要解的就数据码。一个PWM 码的0是由一个0.58ms的低电平和一个0.58ms的高电平 -code is a PWM pulse width modulation code, which is composed of 9MS to I and decent low-level guide pulse, sixteen sy
fhe-AD574
- 数据没有处理，为AD574本身所采数据，不受力时显示2048为零值-data is not, by itself for AD574 mining data from 2048 show that power to zero
C8051_I2C_E2PROM
- 摘 要： 本文件是C8051单片机I2C总线读写测试程序；将跳线器JP6短接，使用外部22.1184MHz晶振. 功能：定义 0 ~ 9 键为数字键， A ~ F 为功能键。按 A 键后，可按0 ~ 9 数字键， 从零地址开始存储该键值，并送LED数码管上显示该键值。按 C 键停止后，按 B 键， 从零地址开始读取数据值，并送LED数码管上显示。读取速度每秒一次。在按 C 键停止后，可按 A 键重新输入。 -Abstract : This document is C8051 MCU
danpiankongzhidainji22
- 初学者:单片机控制电机 （36H）是系统给定值；（34H）是位置反馈值；（4CH）是满位的值；（4AH）是零位的 值；（4EH）是决定系统精度的死区的值；P2.1控制电机正转；P2.0控制电机反转；P2.2是 报警输出；P1.3是外界位置保护输入；电机采用反转制动； L04B3H:-beginners : SCM control motor (36H) is a system for setting; (34H) is the position feedback value;
PWM-c51
- 零耗时低频宽脉冲软PWM信号控制Keil C51演示程序，转摘！-zero time-consuming low-bandwidth pulses Soft PWM control signal Keil C51 demo program, journals!
source-code-of-brushless-motor
- 无刷电机驱动器源代码。基于无传感器方案的无刷电机启动器。核心是换向角度检测：即电机反电势波形数据处理，经过衰减滤波，取出过零相位。应为低速反电势波形dB过小，波形扰动太大，本程序还不能稳定处理10Hz以下的换向计算。,Brushless motor driver source code. Program based on the sensorless brushless motor starter. Is the core to the point of view for detection:
SCR.rar
- STC12C5412AD做的温度检测控制的源程序.有AD检测,可控硅过零触发,PID算法.,STC12C5412AD make the temperature measurement and control of the source. Have AD detection, zero crossing triac trigger, PID algorithm.
iv_4_20ma
- 介绍如何简单可靠而方便测量 4～20mA 信号的文章。许多仪器仪表在远距离传送信号时，都有可能采取 4～20mA 的方式进行传送。本文对使用运算放大器或者不用运算放大器的场合都有介绍。给出了接口电阻的计算方法以及调整4mA＝零点，20mA＝满度的详细说明。并附有局部连接的原理图。-How simple, reliable and convenient measurement of 4 ~ 20mA signal article. Many instruments in the long-dist
0329
- 线路零序保护PSCAD模型，仅供大家参考-Zero-sequence protection PSCAD model, only for reference
dfdf
- 晶闸管的触发方式有移相触发和过零触发两种.files-SCR trigger a phase shift means trigger and trigger two zero. Files
ADC08004-1CD_PHILIPS_159082
- The ADC0803 family is a series of three CMOS 8-bit successive approximation A/D converters using a resistive ladder and capacitive array together with an auto-zero comparator. These converters are designed to operate with microprocessor-control
dis_control
- 一个计时器程序，可显示到59：59，后清零，也可重新清零或暂停。并用LCD显示。-A timer process, can be displayed to 59:59, after the zero can also be re-cleared or suspended. And LCD display.
0832_123
- 并行接口电流输出型DA转换器的控制，包括延时子程序，完成一次转换子程序，完成满值点验证、零值点验证子程序等-Parallel interface current output type DA converter control, including the delay subroutine, subprogram to complete a conversion to complete the full validation data points, zero-value point of au
18b20
- DY580实验板上面的18b20温度传感器程序，精确到0.1摄氏度，支持零下温度。-DY580 board temperature sensor 18b20 above procedures, accurate to 0.1 degrees Celsius below zero temperature support.
temperature
- STC12C5412AD做的温度检测控制的原理图.有AD检测,可控硅过零触发,开关电源.-Detect STC12C5412AD make the temperature control schematic. Have AD detection, zero crossing triac trigger, switching power supply.
8WSMGMB
- 8位数码管秒表计时显示实验,拔掉JPLED跳线 使LED不显示初始状态8位数码管显示0000000.00按独立按键，计时开始 再按一次 计数停止 按第三次 计数值清零 -8-bit digital tube display stopwatch timing experiments JPLED jumper pulled out so that the initial state LED does not display an 8-bit digital tube display 0,000
ZCross
- 220V PWM on ATTiny13 + optoisolated zero cross detector
Zero-Detector
- the Zero Detector Project with ATMEGA16 i guess the name describes it-the Zero Detector Project with ATMEGA16 i guess the name describes it..
zero-tracking
- 零点跟踪功能是称重仪表的重要功能。本资料详细解说零点跟踪的实现及实现代码-Zero tracking function is the important function of the weighing instrument. The information detailed explanation of zero tracking to achieve and the implementation code