搜索资源列表
51单片机系统中运用电脑上的大键盘
- 51单片机系统中运用电脑上的大键盘！ Keyboard接线 PS/2--------51 1 DATA------P3.4 3 GND 4 VCC 5 CLK-------P3.3 接在51的外部中断，触发方式为低电平 AT89x51使用12M Modified by Shen Peng! Postgraduate of 2003, 7 Department Harbin Engineering University-51 microcomputer system on the use of t
lcd2
- 利用KEIL C51语言编写的T6963C液晶驱动程序,头文件有具体的连接定义和汉字字库,只要硬件连接好,一定可以运行,不象有人纯粹为了下载别人的代码-use KEIL C51 prepared by the T6963C LCD driver, the first document linking specific definition and Chinese character, as long as the hardware connection, and will be able to
LCD320A
- 320*240点阵液晶(sed1335)驱动程序,keil c调试通过,总线连接方式-320 * 240 dot matrix LCD (sed1335) driver, c51 c debugging, bus connection
lm128645
- 用AT89C52并口连接LM128645液晶块的有用的汽车ABS故障检测仪程序,LM128645总共20管脚.-parallel port connection with AT89C52 LM128645 LCD block a useful vehicle ABS fault detector procedure LM128645 a total of 20 pins.
153s1to3ASM
- 使用EMC78P153S单片机实现手机一机三卡切换的ASM程序,注释中说明了电路连接方法,其中巧妙之处在于利用外部时钟控制芯片的休眠节(切换时用104电容维持供电).-EMC78P153S MCU use a phone card for three to switch the ASM procedure, Notes note of the circuit connection method, The trick of which lies in the use of an external
pio
- 基于80C51F020的16路开关量两路模拟量控制通用程序，使用两个独立232串口于PC连接-80C51F020 based on the 16-way switch two analog volume control common procedures, the use of two independent 232 serial port on PC Connection
AD_ASM_AD0832shuzidianyabiaoLED
- 数字电压表 AD芯片： 采用8位串行A/D转换器ADC0832。 ● 8位分辨率，逐次逼近型，基准电压为 5V ● 5V单电源供电 ● 输入模拟信号电压范围为 0～5V ● 有两个可供选择的模拟输入通道 显示： 使用三个数码管。 显示范围： 0.00 － 5.10 （单位：V） 连接方式： AD_CLK → P1.0 AD_DAT → P1.1 AD_CS → P3.4 模拟输入 → CH0
yq9
- 单片机与上微机通信的汇编语言程序 支持485传输协议，软件用modbus协议编写-SCM and computer communications on the assembly language support, 485 transmission agreement Software modbus connection with the preparation of the agreement
8019_89s52_asm
- RTL8019芯片与AT89S52单片机的连接程序,,本人用ASM汇编语言所写,极具参考价值-RTL8019 chip microcontroller AT89S52 connection procedures. I used ASM written assembly language, great reference value
RB_24C16_KC
- 本程式是使用C++寫單片機的軔體程式, 可以和PC做串列埠COM port通訊, 也結合I2C通訊標準, 將接收的資料燒錄傳輸至硬件IC 24C16-The program is written using C SCM NERO program that can be done and the PC COM port Serial Port communications, also in connection with I2C communications standard, will rece
TCPmodbushy
- tcp/modbus应用程序,实现了UDP,TCP,把串口通信转换成网络通信-tcp / modbus connection application procedures, the UDP, TCP, put into serial communication network communication
51asn
- 设计的温度采集模块是应用一个滑动变阻器通过改变电阻值进行模拟的温度值改变情况；模数转换模块是运用ADC0809芯片进行模数的转换，把采集到的模拟电压值变为数字值；单片机控制系统通过程序判断此数字值的大小，这样控制温度报警模块，一方面控制发光二极管的亮灭情况，另一方面控制蜂鸣器的报警；温度显示模块应用四位数码管显示模拟的温度值。因此，构成了此模拟的温度控制系统。本系统主要实现了模拟的温度值在30到60的一个设定范围内，正常显示温度，一旦超过了此范围，就会有报警。-design of the tem
0809_sourse
- 0809模数转换原码。ADC0809虽然是一款比较旧的芯片，但是目前好多模数转换芯片都是基于ACD0809设计的。-0809 analog-to-digital conversion original code. A Connection between ADC 0809 is a relatively old chip But now a lot of analog-to-digital conversion are based on ACD0809 chip design.
_-JTAG-Connection
- _ JTAG-Connection.pdf(JTAG-Connection Document)
Driver-Installation-and-Connection-Guide
- Zapp – Z1130 Driver Installation and Connection Guide
P.7---Labview-Connection
- Connecting Atmega32 to Lab-view for Transmitting and receiving Some Specific Data. this project can be used for Lab-view And AVR-MCU Connection.
Domain-connection
- 用于建立域名连接用的代码，能够使之与域名建立连接-For establishing domain connected with the code, and enable to establish a connection with the domain name
GPRS-connection-to-the-server
- 通过gsm模块进行gprs连接，能够上网，可以有其他功能开发-Through the GSM module GPRS connection, to get to the Internet, you can have other function development
Bluetooth-4.0-connection
- 蓝牙4.0配对 绑定 实例源码，for TICC2541 2540-Bluetooth 4.0 connection source for TICC2541 2540
GPRS-connection-to-the-server
- GPRS连接服务器，普通单串口单片机程序，本程序运行后如果gprs模块找到服务商信号，就会连接指定的服务器。-GPRS connection to the server, ordinary single serial microcontroller program, after the program runs if gprs module to find service providers signal, it will connect to the specified server.