搜索资源列表
H30
- 用伟福Lab2000P单片机实验仪上80C196的HSI功能统计输入的脉冲个数。可以用板上500KHz信号和单脉冲的输出相‘与’得到一定个数的输入脉冲。
LED
- STM8SLED例程，使用HSI为系统时钟源，并配置恰当的分频比； TIM2 CC2 输出PWM信号控制LD2亮度； TIM3 CC1 输出PWM信号控制LD3闪烁频率； TLI（PD7）中断用来打开/关闭LD4.-STM8SLED routine use of HSI for the system clock source, and configure the appropriate divide rat
CSS
- 将时钟源由HSI切换到HSE； 使能CSS功能；LED闪烁。-HSI clock source is switched to the HSE enable CSS feature LED flashes.
Music
- 使用HSI为系统时钟源，并配置恰当的分频比； Timer2 CC1通道配置为PWM模式用以驱动蜂鸣器； Timer4 溢出中断用作LD4，LD3，LD2闪烁的时基； TLI（PD7)中断（用户按键）用来切换音乐的音调；-Use the HSI for the system clock source, and configure the appropriate divide ratio
UART
- 使用HSI为系统时钟源，并配置恰当的分频比； LINUART配置为UART模式-Use the HSI for the system clock source, and configure the appropriate divide ratio LINUART configured for UART mode
Sinwave
- 使用HSI为系统时钟源，并配置恰当的分频比； Timer1 CC1，CC2，CC3通道配置为PWM模式；-Use the HSI for the system clock source, and configure the appropriate divide ratio Timer1 CC1, CC2, CC3 channel is configured to PWM mode
80C196KB_UsersGuide_intel
- intel 196单片机手册，讲了单片机内部寄存器配置，io，hsi，等等好些东西。对于196单片机使用者这个文件是必须的 -SCM manual intel 196, speaking of the microcontroller internal registers configured, io, hsi, so better things. 196 MCU file for the user is required
SCM-program
- 用HSO.0输出脉宽为2ms，周期为3ms的方波，用HSO.2输出脉宽为3ms，周期为6ms的方波，并用HSI检测HSO.2输出方波的频率和脉宽。将测量结果循环显示在LED上，要求脉宽值和频率值各显示10秒。-HSO.0 output pulse width as 2ms, cycle square wave 3ms, HSO.2 output pulse width as 3ms, the cycle is 6ms square wave, and using the HSI Detect
SYS_conf
- STM32F407时钟，中断配置头文件，该文件包含HSE,HSI,LSE,LSI,I2S,MCO时钟的初始化； PLL时钟配置，PLL,SYSCLK，HCLK,PCLK1，PCLK2时钟的配置； RCC,GPIO,EXIT,NVIC的配置；-STM32F407 clock, interrupt configuration header file that contains the HSE, HSI, LSE, LSI, I2S, MCO clock initialization PLL
sys23
- STM32F407时钟，中断，精确延时配置，该文件包含HSE,HSI,LSE,LSI,I2S,MCO时钟的初始化；PLL时钟配置，PLL,SYSCLK,CLK,PCLK1，PCLK2时钟的配置；RCC,GPIO,EXIT,NVIC的配置.-STM32F407 clock, interrupt, precision delay configuration, the file contains HSE, HSI, LSE, LSI, I2S, MCO clock initialization PL