搜索资源列表
ckhub
- 该程序为USB HUB程序，其作为开发USB HUB类型的产品很有帮助。-procedures for the USB hub procedures, as the development of types of USB hub products helpful.
wanterHUB
- 水控HUB的程序，主要负责和POS机和PC的通讯，将从POS机传来的数据，打包发送到PC机
ok
- 基于18f4550ICD2、16F877的PIC单片机烧写器仿真器ICD2制作源码 错误更正：877的RA4口要上拉一个5K电阻,R11<4R7,74hc07不行必须用74LS07 如果想重烧IC，4550的CONFIG请参考BMP文件 1。调试时最好有一个有保护的HUB，分步进行 2。焊好后，电位器旋到0，不插队IC，通电测各点电压，并调好12V 3。只插4550，连PC，应能发现新硬件，重点查晶体，USB电压， 4。插好所有I
Hub
- 飞思卡尔08单片机程序，其功能通过串口为接收上位机（PC机等）的指令，解码后，通过CAN总线发往下位机-FreescaleMCU, and its function through the serial port for receiving host computer (PC, etc.) of the Directive, decoded, issued down through the CAN bus bit machine
reference
- Cypress USB Hub Chipset CY7C65620-56LTCX datasheet and relative Schematic, circuit
Radar
- 无线雷达盒信号读取，很有用的源码，值得借鉴。-Radar hub access
HUB_128
- Modbus HUB源程序，使用AVR M88单片机实现，调试通过，可以将ModBUS地址重新映射，方便组网-This is a ModBUS HUB program for C。
hub
- use píc6f887, control 4 face clock
GL850G_USB_HUB.RAR
- 基于GL850G的USB HUB的原理图和pcb-电子电路图-The USB HUB based GL850G schematic and pcb-electronic circuit
Temperature-Control-System
- 利用单片机作为中枢，使用DS18B20作为温度传感器，通过液晶显示模块显示实习温度及操作系统内容，通过按键设定温度范围。通过C语言程序编写代码实现温度检测控制与报警功能-SCM as a hub, use the DS18B20 temperature sensor , LCD module displays the attachment of the temperature and content of the operating system , set the temperature ra
NUC130LC1CN
- 这是基于新塘M0 NUC130LC1CN的CAN集线器开发，四个CAN之间的数据进行相互交互，数据可靠性高，使用方便-This is based on the Xintang M0 NUC130LC1CN CAN hub development of data between the four CAN interact with each other, data reliability, ease of use
Web-Server_10M
- LPC2368学习板网络例程，单片机程序，使用时用交叉线连接，若用交换机或集线器，请使用直通线 -Learning board LPC2368 network routines, SCM, when used with a crossover cable connection, if using a switch or hub, use straight lines
USART_HUB
- STM32F103VCT6的5个串口做一个串口HUB，一个做为上端，4个做下端进行数据透传-5 serial STM32F103VCT6 make a serial HUB, as an upper end, a lower end 4 do transparent transmission of data
ucos_usb_host_ser_detectd
- 使用UCOSII，移植LINUX的HUB驱动，能够检测配置HUB(Using UCOSII, the HUB driver that transplants LINUX, can detect configuration HUB)