搜索资源列表
TestXF
- 在DSP开发板上调试通过的XF引脚测试程序，可以使发光二极管交替闪烁-in DSP development board debugging XF pin through the test procedure can alternately blinking LED
DSP2812GPIOtest
- 使用了TI的2812型DSP，在CCS下编译，用与测试DSP的GPIO口的输入输出功能，通过 LED的闪烁来加以相应。-The 2812 uses the TI-based DSP, under the CCS compiler, use and testing of DSP s GPIO port input and output functions, through the blinking LED to be appropriate.
DSP_C20x
- 一排灯的不同闪烁情况。用一维数组定义五种霓虹灯的闪烁状态。适合初学者。-A row of lights flashing in different circumstances. Using the definition of five one-dimensional array of blinking status lights. Suitable for beginners.
EX2_ASM
- 汇编程序所在目录ex2_asm 。 C 语言程序所在目录ex2_c 。 在CC2000 中的操作如下： 1. Project->Open ，打开该目录中的工程文件。 2. Project->Rebuild ALL, 编译链接 3. File->Load Program 4. Debug->GO Main 5. Debug->RUN （快捷键F5） 即可看到最边上一个LED 周期性的闪亮。灯的闪烁频率由软件中的定时器
EX2_C
- 汇编程序所在目录ex2_asm 。 C 语言程序所在目录ex2_c 。 在CC2000 中的操作如下： 1. Project->Open ，打开该目录中的工程文件。 2. Project->Rebuild ALL, 编译链接 3. File->Load Program 4. Debug->GO Main 5. Debug->RUN （快捷键F5） 即可看到最边上一个LED 周期性的闪亮。灯的闪烁频率由软件中的定时器
ex3_LED
- 程序所在目录：ex3_LED 打开CC2000,进行如下操作： 1. Project->Open ，打开该目录中的工程文件。 2. Project->Rebuild ALL, 编译链接 3. File->Load Program 4. Debug->GO Main 5. Debug->RUN （快捷键F5） 可以看到的现象为：最边上一个LED 不断闪烁（这个LED 在后面其他的程序中都被定义成在定时器中断中闪烁）。其余的4 个
LED_Blink_(C)
- code for blinking of the LEDs on EZ-kit lite bf5-code for blinking of the LEDs on EZ-kit lite bf533
Timer-LED
- 闻亭TDS2407EA的LED程序，用定时器中断控制，产生比普通延时程序更精确的延时闪烁-Wintech TDS2407EA the LED process, using the timer interrupt control procedures than the general delay blinking more accurate delay
led
- led blinking with tms320c5509
Lab1
- Blinking LED on MSP-EXP430F5438 experimenter board.
led
- 基于TMS320VC5416的定时器编程，DSP工作在8MHZ主频，定时器分频系数为15，通过DSP通用I/O引脚控制指示灯闪烁，指示灯每秒闪烁1次。-TMS320VC5416 timer based programming, DSP working in 8MHZ frequency, the timer frequency factor of 15, through the general-purpose DSP I/O pin control light is blinking, the
led_c
- This program is used for blinking leds with different frequencies. A DSP processor is connected to the computed system and CCS studio interface software should be available. Four LEDs are available on the processor kit. This program makes the 1st LED
LED-BLINKING
- for led blink in dspic-for led blink in dspic33
led_flash
- DSP-C5402入门简易程序之硬件闪烁灯测试程序-DSP-C5402 entry-summary of the test program hardware blinking light
02_GpioLed02
- 将PWM1-PWM6引脚配置为I/O口，方向为输出。在GPIOLed01.pjt的基础上， * 通过使用T1定时器的周期中断，每隔1s改变一次LED灯亮或者灭这种状态 * 所保持的时间，也就是说改变了LED灯闪烁的频率-The PWM1-PWM6 pin is configured as I/O port direction for output. On the basis of the GPIOLed01.pjt,* the timer by using the T1 period i
new-LED-Blinking-1
- TO blink a LED using ARM7 processor
Two-LED-Blinking
- 学习TMS320F28335时写的简单的GPIO翻转程序，控制两个LED灯的亮暗，间隔一秒左右。-TMS320F28335 GPIO toggle.
CORE_LED
- 该程序是针对ti的TMS320C6747新品的GPIO引脚的LED闪烁功能，在CCS环境下可实现，以及经过验证，可以执行。-The program is for TI TMS320C6747 new GPIO pin LED blinking function can be realized in the CCS environment has been verified, you can perform.
ADC7656
- 该程序是针对ti的TMS320C6747新品的GPIO引脚的LED闪烁功能，在CCS环境下可实现，以及经过验证，可以执行。-The program is for TI TMS320C6747 new GPIO pin LED blinking function can be realized in the CCS environment has been verified, you can perform.
lab1-GPIO_LED
- F28335C的开发例程，实现LED灯的闪烁-Sample programs of F28335C: Blinking of LED