搜索资源列表
mon51(sst89c58).asm
- sst89c58下载器，使用keilc51的debug调试器下载。将本程序编译后写入sst89c58，并编程为remap 4kbytes。该芯片即有了keil环境下载功能,当p1.0拉低时，启动时进入下载程序，进入下载程序后将会自动删除block0,p1.0高电平时进入用户程序。 进入下载程序后，可以通过串口和keil的仿真环境连通，波特率自动调节,选择load HEX文件，即可将程序下载到sst89c58的低端32keeprom中。除了7e00-7fffh被占用-sst89c58 down
jflashsource
- 非常经典的用并口作为jtag工具的源码。首先是需要装入并口的驱动，然后模拟jtag命令波形。-very classic use of the parallel port as a source jtag tools. First is the need to load the drivers parallel port, and then ordered jtag simulation waveform.
CAN_kuozhan
- CAN总线资料， CAN.sch 是protel99se格式文件 CPLD目录是7032的CPLD工程，使用MAX+PULS10.0 test目录是程序工程目录，使用ADS1.2编译该工程，load到SDRAM调试
AD7705(C51)
- 1，初始化： 如果AD7705复位引脚直连VCC，最好在初始化程序中加入初始化序列，不然ready信号不会输出。 2，输入范围 如果AD7705采集单端信号，则输入必须在0到VDD之间，而不可以超出或为负，如果一个输入为负，则另一个输入会有灌入电流的现象，芯片无法正常运行。-AD7705 is a complete 16-bit A ö D converter. Within Structure in Figure 1. If the external crysta
ejtag-0.2
- mips e-jtag 加载uboot程序，实现直接控制cpu加载boot loader，无需事先烧写任何程序进flash-mips e-jtag loading uboot procedures to achieve direct control of the cpu load the boot loader, any program without prior programming into flash
current
- This interface to cypress usb chip to load values in its memory-This is interface to cypress usb chip to load values in its memory
S3C2440A_Nand_Bootloader
- 由于Nand Flash不能直接线性的访问，所以对于烧到Nand的上的程序，处理器无法直接执行，为了解决这个问题，S3C2440A在内部设置了地位于0x0000_0000容量为4Kbytes的SRAM，在处理器上电时会通过内部电路自动把Nand里头4k的程序（bootloader）装载到SRAM执行，这里称其为小程序，小程序执行后 再装载Nand里位于4K以后的大程序到SDRAM执行。-As Nand Flash can not directly access a linear, so
RT9163-33CG-datasheet
- The RT9163 is a positive low dropout regulator designed for applications requiring low dropout performance at full rated current. The device is available in fixed output voltage of 3.3V, 3.5V, and 5.0V. The RT9163 provides excellent regulatio
CLK_SETKEY_ALM
- code PIC16F877A ,this project is control turn on ac load with clock count up 4 digit it star 0-24Hour.
vmdialer-0.12.tar
- VMDialer is used to do the following things with the Virgin Mobile Broadband2Go/Verizon Wireless Novatel USB760 under Linux: * Automate the switch from mass storage mode to modem mode. * Automate the driver load and loading of the dialer.
RTC_UART
- rtc using uart we can load rtc registers value direcly through the hyperterminal by making use of this program.the rtc used here is ds1307
i412.tar
- Source code of a bios for MachZ, an i486 SoC Permit launch of a vxWorks or Linux MachZ have an internal ROM to load software in i486 cache
loadshed
- load shedding for kseb
MJ
- 导入方法：在CAD菜单中选择工具-autolisp-加载-启动组-添加（mj存的位置），以后自动加载。 里面有用法，输入mm选择需要计算面积的pl线可以直接求和。 mt设置字高。 -Import method: in the CAD menu, select Tools-autolisp-load- Startup group- add (mj deposit position), after loaded automatically. There are usage, selec
adc_interrupt
- this is c source code for reading a adc of c8051f040 microconverter in interrupt mode to reduce the load on cpu.
ARM-analysis-ELF-source-code
- ARM2440下分析ELF文件并加载，ads下编译-2440 analysis of the ELF file and load, ads compiled
x-load-1.41
- 这是ti CORTEX A8处理器 OMAP3530的X-Loader 在pandaboard验证通过！ -This is ti CORTEX A8 OMAP3530 processor, the X-Loader in pandaboard verified by!
BMP-ARRAY
- Can use it to run on MS-DOS or VC++, it converts you Bitmap image to C style Arrays for sprites or pictures you want to load on LCD using embedded systems.
001162
- This portable network service monitor was developed to help network administrators supervise datacenters. The handy monitor—which The well-designed DMX Portal is an affordable DMX lighting controller. You can use the novel system to remotely control
simple-eload
- 基于MSP430F149开发的简易直流电子负载，采用内部12位AD，外围硬件电路的负载电流可达1.3A，测试电流精确度高，采用18V自动过压保护。-MSP430F149 development simple DC electronic load, internal 12 AD, peripheral hardware circuit load current of up to 1.3A precision test current, using 18V automatic overvoltage