搜索资源列表
src_mp3
- The program was written with some object-orientation in mind, which means that all functions that operate on a certain structure, has the structure s name as prefix in the function name, for example \"Bitstream_get\" which gets bits from a bitstream
SPWMsine
- 利用avr atmega128芯片编写的spwm程序，通过PB0、PB1两个IO口数出相位相差180度的SPWM波形。-spwm program for avr atmega128 microprocessor,the wave output from PB0 and PB1 I/o.
test
- 凌阳61板模拟红绿灯程序，适合新手熟悉I/O口的使用-Sunplus 61 board simulated traffic light program, suitable for novice familiar with the I/O port to use
cpu_module_cy8c21434
- A valid project to test timer,uart,adc, i/o peripherals in the psoc cy8c21434. The project e source are tested with the psoc designer 5.0. The hyperterminal program is used to display the results
at24c64
- AT24C64串行读写程序 用普通I/O口进行总线模拟-AT24C64 serial reading and writing program with the ordinary I/O port for bus simulation
balance-
- 自平衡小车整体源代码，包括主程序，卡尔曼滤波，串口通信以及I/O口的使用。-Self-Balancing Robot overall source code, including the main program, the Kalman filter, the use of serial communication, and I/O port.
lab1
- 练习一I/O控制 练习目的:1.掌握单片机I/O口控制方法。2.掌握Keil与Proteus的使用方法。练习内容：参考例程，掌握Keil与Proteus的联调使用方法。画出电路，编写一段程序，用P1 口作为控制端口，使8个LED 轮流亮。画出电路，编写一段程序，用P1.0~P1.6 口控制LED，P1.7 控制LED 的亮和灭(P1.7 接按键，按下时LED 亮，不按时LED 灭。)-Exercise I/O control, practice the purpose of a master M
Responder
- 摘要：单片机具有稳定可靠、 体积小、 价格低廉等特点，成为设计智能化仪器仪表的首选微控制器，因此本次设计我们采用了AT89C52芯片，此款单片机可以使用软件对其进行在线编程，其灵活性和可靠性都相对提高。本设计中的电子钟的核心是AT89S51单片机，其内部带有4KB在线可编程Flash存储器的单片机，无须外扩程序存储器，硬件电路主要由四部分构成：时钟电路，复位电路，键盘以及显示电路。系统时钟电路采用的晶振的频率为12MHz，定时计数个数为5000，定时器采用的是定时器0工作在方式1定时，用于实现时
P&O of MPPT
- FILE: Colltroller of Buck DC-DC Converter.c // TITLE: P&O of MPPT by disturb of Input Voltage (Vref+/-deltaV). // ASSUMPTIONS: // This program requires the DSP281x V1.00 header files. // As supplied, this project is configured for "boot to H
Ald20120517AO
- 这是一个西门子PLC300的控制程序。有多路I/O，通过PLC内部的PID模块进行温度控制。控制精度在0.1摄氏度。-This is a SIEMENS PLC300 control program. There are multiple I/O, through the PID internal PLC module for temperature control. The control precision at 0.1 degrees celsius.
a-segment-single-dispaly
- 7 segment display program using keil c is for LED on /O-7 segment display program using keil c is for LED on /OFF