搜索资源列表
Alpha_V1.1
- 电机ADC驱动文件，方便使用，适用于工业控制-Motor ADC drivers, easy to use, suitable for industrial control
m16-19264oscilloscope
- M16-19264示波器 位 定义 默认 ＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝ 0 运行状态 运行 1 触发模式 上升沿 2 画点模式 连线 3 DivY 4 Output_Freq 5 DivX 6 触发电平 7 频率 -M16-19264 oscilloscope define default bit Operation Status 0 1
power-circuit
- 在电源输入的前端利用旁路去耦电容滤波器，在+12V输入时，首先通过一个电解电容C1和电容C2保证电压的输入稳定，之后选择利用稳压器NCP1117ST50T3G将输出电压降到+5V，如图3.5所示，其输出电流为1A。在稳压器之后继续采用一个电解电容C3来保证输入到芯片的供电电压稳定。-Power input at the front end of the use of bypass decoupling capacitor filter when+12V input through a first
communication-circuit
- 由于RS232的电平与Arduino Mega 2560的接口电平不能兼容，所以就需要进行电平的转换，即进行串口转换模块的设计，本文选择利用ATMEGA16U2-MU模块来做电平转换，将上位机的指令通过此模块发给下位机-Since the RS232 level is not compatible with the Arduino Mega 2560 interface level, so we need to level conversion, that is designed to seri
core-circuit
- ATmega2560通过USB接口与PC进行传输，供电电压为5V，内部晶振为16MHz。该芯片共有有54个I/O引脚，特别适用于需要大量I/O口电路，其中的16个可以提供脉宽调制（PWM）模拟输出，还有另外16个模拟输入引脚。在通信方面，有4个硬件串口，另外也可以支持SPI通信和I2C/TWI设备。设计核心电路中加入复位按键，通过USB串口进行通信。-ATmega2560 through the USB interface with the PC for transmission, power
PWM
- 用C语言编写的可实现产生PWM波,已经下载到单片机产生了PWM波，用于高压脉冲电源的设计。-Written in C can be implemented to generate PWM wave has been downloaded to the microcontroller generates a PWM wave for high-voltage pulse power supply design.
Power-supply-acquisition
- 可调稳压电源，基于单片机STC12C5A60S2，可调稳压输出，7段共阴数码管显示。1.25V至37V，精度0.1v。-Adjustable power supply, based on single-chip STC12C5A60S2, adjustable voltage output, 7-segment common cathode digital display. 1.25V to 37V, the accuracy of 0.1v.
ALINX9226
- 黑金出的学生练习板，双ad9226采集，两路输入5v以内的信号，自带衰减电路。-Black gold out of the students to practice the plate, double ad9226 collection, two input signals 5v within, comes attenuation circuit.
CC1101-LAYOUT
- 这是参考官方设计手册做的一个CC1101模块，实测有效直线通信距离200米，绘制环境AD16(附51，MSP430程序设计参考资料以及TI PCB参考设计)-This is the official reference manual designed to do a CC1101 module, found effective communication distance of 200 meters straight draw Environment AD16 (Annex 51, MSP430
PROTEUSfz
- Proteus 大量仿真实例，很好的学习单片机学习资料，欢迎下载-Proteus a large number of simulation examples, learning good information, welcome to download
ZNXJXC
- 智能循迹小车全部资料,含C语言源程序，PCB图，欢迎下载-Intelligent tracking car all the information, including C language source program, PCB, welcome to download
VGA_SHOW
- 利用VHDL语言基于DE2-115的开发板在显示器上实现自选图片的显示。-Using VHDL language based DE2-115 development board on display managed to achieve image display.
1
- 芯达STM32 V2.1原理图 芯达STM32 V2.1原理图-Core up to STM32 V2.1 schematic
AD7731DATA
- 将AD采集的串行数据转换为并行数据，上传到ARM中-The serial data collected by AD is converted to parallel data, and uploaded to ARM
1
- 基于multlism软件和常用的三极管等基本期间，实现三端式稳压电源设计-Based on multilingual software and commonly used transistors and other basic period, to achieve three-terminal power supply design
ractical-electronic-
- 电子实例操作diy，有图有步骤有电路图,简单易于操作，是喜欢DIY朋友不可多得实例指南。-Electronic examples of operation diy, there are plans to have a circuit diagram
MP2307
- MP2307,电源电压基准芯片，电源电力电子领域常用芯片。-MP2307，a monolithic synchronous buck regulator. The device integrates 100mΩ MOSFETS that provide 3A of continuous load current over a wide operating input voltage of 4.75V to 23V. Current mode control provides fast
Slide
- 北航与慕尼黑工业大学 飞行器课件 讲解四轴飞行器的空气动力学模型，位姿控制PID -Northern Technical University of Munich and courseware to explain Quadcopter aircraft aerodynamic model, pose PID control
CF2.0
- 国外著名小四轴飞行器Crazyflie 2.0原理图，可以参考其制作pcb-Famous small Quadcopter Crazyflie 2.0 schematics, refer to its production pcb
vlsi-design3
- 电路具有四路4_bit字宽的串行输入总线，四路4_bit字宽的输出总线信号的电路。 电路完成将串行输入信号A[3..0]、B[3..0]、C[3..0]、D[3..0]（大小排列无序）以数值大小排序输出的功能，输出X3[3..0]、X2[3..0]、X1[3..0]、X0[3..0]中X3最大，X0最小。输入数据是无符号整数。 -Circuit with four 4_bit word wide serial input bus, four 4_bit word wide output