搜索资源列表
Air200_硬件设计手册_V2.3.pdf
- Air200模块是四频段GSM/GPRS模块,本文档定义了Air200模块及其硬件接口规范,电气特性和机械细节,通过此文档的帮助,结合我们的应用 手册和用户指导书,客户可以快速应用Air200模块于无线应用。(The Air200 module is the four band GSM/GPRS module. This document defines the Air200 module and its hardware interface specifications, electrica
Air200模块开发板S1,S2使用说明V1.2.pdf
- Air200 模块开发板是专用于 Air200GPRS 模块在 Luat 开源环境下的开发实验板。(The Air200 module development board is dedicated to the development of Air200GPRS modules in the Luat open source environment.)
Arduino_20150411
- ArduCAT是Arduino Compatible 开发板。本产品力图通过Arduino技术，大大简化EtherCAT从站的开发。ArduCAT开发板包含两路可用于EtherCAT实时以太网的100BASE-TX网口，所以它特别适合基于PC的自动化方案。ArduCAT使用ATMega1280 处理器，兼容Arduino Mega开发板，并具有完全相同的引脚定义。板上采用开关稳压器提供5V 或3.3V的2A直流输出，且发热甚微。除配套的开源Arduino库外，还配有从站应用层代码自动生成工具，
SwiftProForArduino-develop
- 这个是UArm的开源控制软件 以及固件 对于参考机器臂开发很有帮助。定位精度已经达到0.2mm 而且 还有手势教学功能(This is UArm's open source control software and firmware, which is very useful for reference robotic arm development. Positioning accuracy has reached 0.2mm, and gesture teaching function)
uArmCreatorStudio-master
- 上位机软件 也是开源的 ，带3D直接视图功能，直观显示轨迹 与图形化变成(The host computer software is also open source, with 3D direct view function, intuitive display of trajectory and graphics into)
V036电调
- 这里有无刷电调资料分享，资料齐全，里面包括了原理图，pcb文件，还有源程序和中文注释(There are brushless data sharing, data is complete, including schematics, PCB files, as well as source code and Chinese Notes)
led时钟成熟可用代码
- led时钟成熟可用代码,DS321,GPS,红外遥控(LED clock is mature and usable code, DS321, GPS, infrared remote control)
CC2530 AD采集内部温度串口显示
- 通过实验掌握 CC2530 芯片串口配置与使用 集到内部温度传感器信息通过串口发送到上位机(Master the serial configuration and use of CC2530 chip by experiment The information collected from the internal temperature sensor is sent to the upper computer through the serial port)
uwb.rar
- 超宽频室内定位，采用STM32与DWM1000模块通信，定位精度达10cm。(In ultra wideband indoor positioning, STM32 and DWM1000 module are used to communicate, the positioning accuracy is up to 10cm.)
adc_send
- 本代码分发送与接收两个模块，发送模块可以采集stm32F4单片机PA5口的模拟电压，通过nrf24l01发送至另一块单片机，该单片机将接收数据发送到串口。(This code is distributed with receiving two modules, sending module can be analog voltage acquisition stm32F4 microcontroller PA5 mouth, sent via nrf24l01 to another piece
EMP7032SLC44
- 这是本人亲自造过的CPLD最小系统图纸，保证可以用，因为造出过实物的，可以找我问问题或者买样品，付材料钱和运费就可以了(This is the CPLD minimum system drawing I made by myself. It guarantees that it can be used, because it can ask me questions or buy samples, and pay for material and shipping cost.)
Xilinx IP核详解和设计开发
- Xilinx IP核详解和设计开发 ，对于学习FPGA的同事非常有帮助(Xilinx IP nuclear detailed interpretation and design and development is very helpful for the colleagues to learn from FPGA)
四线oled
- 这是IIC协议四线OLED屏幕的底层，在KEIL环境下编译，也可以直接调用.C和.H文件(This is the bottom of the IIC protocol four line OLED screen)
stm32实现LX-16A舵机简单转动
- 实现用STM32F1控制穿行舵机LX-16A舵机转动，转动角度可根据舵机使用说明书自己调(The steering gear LX-16A is controlled by STM32F1. The rotation angle can be adjusted according to the steering instruction.)