搜索资源列表
KMG
- 在16383个机器周期内必须至少喂狗一次。 当晶振为11.0592M时在17毫秒内需喂狗一次。 激活看门狗后,喂狗,P2引脚上的LED闪烁发光 激活看门狗后,如果不喂狗,则复位 P0引脚上的LED闪烁发光-16,383 machines in the cycle must have at least one喂狗. When the crystal for 11.0592M domestic demand at the 17 ms time喂狗. Watchdog acti
shanshuo
- 在做界面方面,肯定会遇到闪烁问题,这些文档是本人收集的如何解决闪烁文的,希望对大家有用-Interface aspects of doing, and will definitely encounter flickering problem, I have collected these documents is how to solve the blinking text, and I hope useful for all of us
anjian
- (1)每按下一次开关SP1,计数值加1,通过P0端口的P0.0到P0.3显示出其的二进制计数值; (2)上电的时候,L1接在P0.0管脚上的发光二极管在闪烁,当每一次按下开关SP1的时候,L2接在P0.1管脚上的发光二极管在闪烁,再按下开关SP1的时候,L3接在P0.2管脚上的发光二极管在闪烁,再按下开关SP1的时候,L4接在P0.3管脚上的发光二极管在闪烁,再按下开关SP1的时候,又轮到L1在闪烁了,如此轮流下去。 -(1) Every pressing a switch SP1, c
qicheweidengsheji
- 设计一个汽车尾灯控制器,实现对汽车尾灯显示状态的控制。在汽车尾部左右两侧各有3个指示灯(假定采用发光二极管模拟),根据汽车运行情况,指示灯具有4种不同的显示模式:(1)汽车正向行驶时,左右两侧的指示灯全部处于熄灭状态;(2)汽车右转弯行驶时,右侧的3个指示灯按右循环顺序点亮;(3)汽车左转弯行驶时,左侧3个指示灯按左循环顺序电亮;(4)汽车临时刹车时,左右两侧的指示灯同时处于闪烁状态。-Design a car taillight controller to realize the car ta
PWM
- 关于各种电机的PWM程序: 工程1,采用C语言完成的主要功能有 1:用定时器1中断让LED闪烁; 2:用定时器2的比较单元产生一路PWM; 3:用EVB模块产生6路PWM; 另外四个汇编程序依次分别是: SVPWM(软件法)程序, 交流异步矢量程序, 直流双极性双闭环可逆控制程序, 和采样SPWM程序。 -PWM motor on a variety of programs: Project 1, using C language to complet
LPC2148Test
- blinking led program for arm
Text1
- 利用动态扫描和定时器1在数码管上显示从765432开始以0.1秒的速度往下递减直至765398并保持显示此数, 与此同时利用定时器0以0.5秒速度进行流水灯从左到右移动,当数码管上的数减到停止时,流水灯也停止,然后闪烁3秒后发光二极管关闭,数码管显示“HELLO”,并保持住.-Dynamic scan and Timer 1 in the digital display to 0.1 seconds from the 765,432 rate began decreasing down an
STM32-BLINK-LED-GCC-ECLIPSE-projects
- Some examples for STM32, blinking diodes and others.
main
- PIC16f877 A/D conversion LED blinking
main
- Source file for led blinking
akram-lab-micro-1
- led blinking by 89c51 mcu
AN3279---Blinking-LED-with-Touching-Sense
- AN3279 - Blinking LED with Touching Sense
liushuideng
- 流水灯的各种简单的闪烁:从左至右,奇数闪烁,偶数闪烁,两个一起闪烁等 -Flowing water light a variety of simple blink: from left to right ,odd blinking, even blinking ,two together blinking and so on。
led-blinking
- To build the circuit, attach a 220-ohm resistor to pin 13. Then attach the long leg of an LED (the positive leg, called the anode) to the resistor. Attach the short leg (the negative leg, called the cathode) to ground.
Wattmeter-_needs_R_sense_calculations
- blinking led sim on Proteus
piscabit
- Test the output blinking a bit