资源列表
armsysucosex2
- 本文是根据我学习ARM开发以来的一些经验总结，以自己设计的S3C44B0X板为例，给出入门上手的最基础知识。有些东西只是个人的主观认为，不一定准确，算作抛砖引玉吧，欢迎大家指正！-this paper is based on my study of the ARM since some experience to design its own board of S3C44B0X example, the entry is easily the most basic knowledge. Some
armsysucosex3
- 本文UCOS是根据我学习ARM开发以来的一些经验总结，以自己设计的S3C44B0X板为例，给出入门上手的最基础知识。有些东西只是个人的主观认为，不一定准确，算作抛砖引玉吧，欢迎大家指正！-this paper is based on my study of the ARM since some experience to design its own board of S3C44B0X example, the entry is easily the most basic knowledge.
armsysUDPtest
- 本文UDP是根据我学习ARM开发以来的一些经验总结，以自己设计的S3C44B0X板为例，给出入门上手的最基础知识。有些东西只是个人的主观认为，不一定准确，算作抛砖引玉吧，欢迎大家指正！-This paper is based on UDP, I study the ARM since some experience to design its own board of S3C44B0X example, the entry is easily the most basic knowledge.
2410loadGNU
- 2410 nand boot load!（4K DRAM) 0地址开始运行，没有象VIVI拷贝自身到 高端内存运行，可以用它加载UBOOT。 也可以改写它用来引导自己的系统-2410 nand boot load! (4K DRAM) 0 addresses begin, as VIVI not copy itself to high-end memory operation, can be used UBOOT load. It can also rewrite used t
sorce
- 一个很好的利用verilog编程实现的cpu程序，一定要好好利用。-a good use of the Verilog Programming cpu procedures, we must make good use of.
sz1
- 本程序用at16实现两根线(两个i/o口)+8片74164+一片ULN2003驱动24个LED数码管,通过串口写入要显示的数,可以在很多地方应用 -at16 the procedures used to achieve two lines (2 i / o) are 8 1 74164 24 ULN2003 drive LED digital control through serial write to show that the number can be applied in many
SZ2
- 本程序为CAN总线开发程序,通过串口显示,多台计算机远程数据适时传递,用于工业控制-procedures for the development of procedures CAN, serial, multiple computers remote data transmission time for industrial control
xu3
- 这是f040与2401连接后，进行通信的程序。已经调试通过了 仅供大家参考 第一次传 不好的习惯请大家指正 -This is connected with the 2401, the communications procedures. Debugging has been adopted only refer to the first-bad habit of correcting Thank you, please
7565P3
- 这是一个驱动LCM模块显示的51单片程序，模块点阵是128×64，使用的IC是ST7565P.-This is a drive LCM module shows the 51 single procedure, module lattice is 128 64, the IC is ST7565P.
C++读取GPS程序（WINCE）
- 在wince系统下用c＋＋读取gps的程序-Nicholson systems in C + + using a GPS reading procedures
红外遥控接收
- 红外遥控接收 ORG 0000H LJMP START 转入主程序 ORG 0010H START: MAIN: JNB P2.2,IR LJMP MAIN 以下为进入P3.2脚外部中断子程序，也就是解码程序 IR: MOV R6,#9 SB: ACALL DELAY882 调用882微秒延时子程序 JB P2.2,EXIT 延时882微秒后判断P3.2脚是否出现高电平如果有就退出解码程序
IrComm on CE4.2
- 基于windowas ce4.2的一个ir通信的程序, 使用EVC++编写,提供一个基于sh3处理器的例子-windowas ce4.2 based on the ir a communications procedures, the use of EVC prepared to provide a processor based on CPU example