搜索资源列表
jpeg_network
- 使用evm dm 642开发的DSP源程序，该程序可以通过摄像头读取图像，再使用JPEG压缩算法进行压缩，随后通过evm板的RJ45网络接口通过Internet读取到摄像头的图像。-source code for evm dm 642.this application read image from carma,then compress it by jpeg,send the image through evm s RJ45 to internet.
LS_soft
- 5402控制88796网卡的程序，用于网络开发。提供了网络发送接受等功能-5402 88796 Ethernet control procedures for network development. Providing the network send and receive functions
2407SPI
- 该程序利用LF2407的SPI模块向MAX5121芯片发送数据用于D/A转换，MAX5121的模拟输出端输出一个三角波-the procedures used LF2407 the MAX5121 SPI chip modules to send data for D / A conversion, the MAX5121 output analog output - a triangular wave
CAN2.0
- 关于can总线2.0的发送和接受程序,经项目验证通过,具有极大的参考价值.-2.0 on the bus can send and receive procedures, certification by the project, is of great reference value.
LP_DMA_C
- 老外写的TS201 LinkPort DMA发送/接收程序，学TigerSharc的可以看看。-foreigner wrote TS-201 LinkPort DMA Send / Receive process, TigerSharc the school can look at.
send
- DSP实现TL16C550及RS232串口数据传输（发送端）
dsp28335例程，买开发板送的
- dsp28335例程，买开发板送的，但愿大家有点用途的！,dsp28335 routines, development board to send to buy, and I hope everyone uses a little bit!
F2812_SCI02 PC机串口调试助手
- F2812 SCI与PC机串口调试助手以收发中断方式实现收发数据。（CCS3.3开发环境） 功能：使用SCIA模块和PC机进行串口通信，等待PC机上的串口调试软件向DSP发送"hellodsp"，DSP接收到上位机发送的数据之后，将这些数据发回PC机，显示在串口调试软件中。 说 明：本实验中SCIA模块的发送和接收采用中断方式实现，空闲线模式波特率为19200，通信数据格式为1位停止位，8位数据位，无校验位-F2812 SCI and the PC serial port r
CAN_RX
- F2812 CAN总线接收数据（CCS3.3开发环境下） 实验目的:通过外部其他CAN设备给Super2812发送数据，了解CAN总线的设置和通讯过程，请尤其注意ID的设置 实验说明:将MBOX16设置为接收模式，并采用中断的方式接收数据 实验结果:可以观察变量Rec_h，Rec_l,查看收到的数据-F2812 CAN-bus receiving data (CCS3.3 development environment) Purpose of the experiment:
TMSC3206416串行数据通讯代码
- TMSC3206416串行数据通讯代码，其中包括寄存器的配置，EDMA的配置，及接收数据和发送数据的代码-TMSC3206416 serial data communication codes, including the configuration register, EDMA configuration, send and receive data and code data
IO.rar
- 由拨码开关通过数据线D0-D7向DSP输入0-255数据，DSP收到数据后通过D8-D15向发送收到数据的到发光二极管进行显示,From the allocation of key switches through the data lines D0-D7 to the DSP input 0-255 data, DSP receive data through the D8-D15 to send received data to the light-emitting diode displa
ECAN
- 这是一个CAN总线应用，CAN总线接受和发送的程序-This is an application of CAN bus, CAN bus, the procedures to receive and send
mcbsp2
- dm642的mcbsp接受发送程序，应用EDMA进行搬移数据-dm642' s mcbsp accepted to send a program, application EDMA to move data
emac
- TI 6474 的emac 使用例程，使用88e6122 作为物理芯片，初始化sgmii与mdio,可以向上位机发送数据报文- test code for emac perpheral of dsp tms320c6474,use 88e6122 as phy device and initial sgmii and mdio ,can send ethernet packet to pc
Spi01
- 2812实现SPI的回送测试模式，SPI自发自收，发送和接收采用查询方式实现，将SPISIMO和SPISOMI两个引脚内部短接，实现自发自收模式。SPI将0-99这100个数字逐个发出，然后逐个接收存入Spi_VarRx[]。-2812 to implement the SPI loopback test mode, SPI spontaneous self-closing, send and receive be achieved using query will SPISIMO and SP
can_tx
- TIc6000 32位定点DSP DM6437 CAN总线发送程序-TIc6000 32-bit fixed point DSP DM6437 CAN bus to send program
mcbsp_loopback
- DSP28335的MCBSP接口的驱动程序，类似SPI口的功能，可进行数据的收发-The DSP28335 MCBSP interface driver, similar to the SPI port can send and receive data
CCS-DEMO
- OMAPL138 外设使用经典例程，包括串口和网卡底层接收发送数据包检测工程-OMAPL138 peripherals use the classic routines, including the serial port and network card the underlying receiver to send data packet inspection works
spi_rf905-send
- 基于DSP2812的rf905无线通信发送程序，，原创-Wireless communications based on DSP2812' s rf905 send procedure, originality
CAN-send-and-receive-data
- CAN总线通信程序源码，包括CAN通信主程序设计，CAN控制器初始化程序、CAN发送程序和CAN接收程序-CAN bus communication program design, including CAN bus communication of the main program. Including the CAN controller initialization, CAN send program and CAN receive procedures