搜索资源列表
PmacCtrl_v5.1
- 利用VC编写的PMAC控制芯片驱动程序，用以通过PMAC芯片驱动五轴联动机床。-VC prepared by the PMAC control chip driver, PMAC chip to drive through 5-axis machine tools.
Baxis_gyroscope__IDG300_source
- 二轴陀螺仪IDG300源程序，主要实现姿态实现算法和温度补偿及校准,B-axis gyroscope IDG300 source, the main algorithm realize realize posture and temperature compensation and calibration
adxl345
- avr32 library for ADXL345 3-Axis, ±2 g/±4 g/±8 g/±16 g Digital Accelerometer
plane_complete
- 基于ucgui的打飞机程序 通过扫描按键控制我机移动(只有4个按键,我们就设置了前后左右4个方向按键,子弹设为自动发射) 敌机移动通过rand函数产生(设敌机最大数为ENEMYMAXNUM,只要低于这数,每次循环就产生敌机否则不生成敌机.敌机只会在Y轴移动,如果敌机与我机相撞,,则发生爆炸) 敌机子弹生成与移动(每架敌机子弹数最多为BULLETMAXNUM,低于这个值,每个循环都会在飞机正前方产生一颗子弹,在Y轴方向移动SPEED.Y.如果子弹碰到我机,则发生爆炸,LIFE减
ADXL345
- 三轴加速度传感器的全套资料。应用前景广。消费电子 工业电子 都有用-Full three-axis accelerometer data. Wide application prospects. Consumer electronics industry has used electronic
mpu-6050
- MPU-6000（6050）为全球首例整合性6轴运动处理组件，相较于多组件方案，免除了组合陀螺仪与加速器时之轴间差的问题，减少了大量的包装空间。MPU-6000（6050）整合了3轴陀螺仪、3轴加速器，并含可藉由第二个I2C端口连接其他厂牌之加速器、磁力传感器、或其他传感器的数位运动处理(DMP: Digital Motion Processor)硬件加速引擎，由主要I2C端口以单一数据流的形式，向应用端输出完整的9轴融合演算技术-MPU-6000 (6050) is the world'
CNC_3Axis
- Source code for PIC microcontroller to control 3 Step motor, communicate with PC via LPT port. Application: CNC machine, 3 axis machine-Source code for PIC microcontroller to control 3 Step motor, communicate with PC via LPT port. Application: CNC ma
digitalscale_to_led_and_serial_AVR
- digital scale to serial and 7-seg leds converter (1 axis DRO system)
H195
- 老外搞的卫星接收的电动极轴天线控制电路，老外搞的卫星接收的电动极轴天线控制电路-Foreigners engaged in the electric polar satellite receiver antenna control circuit, foreigners out of the satellite receiving antenna control circuit of electric polar axis
SRB
- ZIGBEE WSN 无线三轴重力加速度传感器网络节点程序-ZIGBEE WSN wireless three-axis gravity sensor network node procedure
NCB
- zigbee无线三轴重力加速度NCB程序，与SRB相对应。-zigbee wireless three-axis acceleration of gravity NCB procedures, and the corresponding SRB.
ADXL345
- Multi-Axis digital accelerometer from Analog Devices
MMA7361V1
- 含有MMA7361Q 3轴小量程加速传感器的说明文件以及一些应用方式。-Small scale with MMA7361Q 3-axis acceleration sensor means the documentation and some applications.
STM32_AHRS_WorkDir
- 这是我从淘宝买的一套很不错的IMU（姿态测量单元）的学习套件，对与初学者来说，很好理解，STM32F103主控制器，集成了MPU-6050（集成3轴陀螺仪和3轴加速器）、HMC5883L（3轴地磁传感器）、BPM085（气压高度计、该传感器在高线性模式下，分辨率为0.03hPa、0.25米，可以满足机器人室内爬楼梯的的高度检测）、STM32F103T8 （32-bit ARM CortexM3处理器运行在72M时钟）-This is a very good buy from Taobao IMU
12864-LCD-6-axis-
- 用MSP430f149采集陀螺仪原始数据，并用12864液晶显示6轴数据-MSP430f149 gyroscope with the raw data collected and used 12,864 LCD 6-axis data
STM32The-4-axis
- STM32 4轴步进电机加减速控制源码, 4轴步进电机加减速控制源码-The 4 axis stepper motor acceleration and deceleration source control
Four-axis-aircraft-source
- 基于STM32和MPU6050的四轴飞行器-Based on the STM32 and MPU6050 four axis aircraft
X-axis-waveform-time
- 波形图X轴时间显示，显示当前波形图的X轴的时间，在labview下开发 -X-axis waveform diagram showing the current time
8-axis-motion-control
- 8轴运动控制卡资料,适合搞运动控制卡的工程师参考-8-axis motion control card data
the-six-axis-sensor-STM32F407
- 本文件是基于STM32F407的六轴传感器的全部文件。-This document is based on all files of the six-axis sensor STM32F407.