搜索资源列表
OMNET_simulation
- WSN仿真一例假定节点0（node[0]）周期性广播消息其它节点接收到消息并转发出去-Sensor Simulation case assumptions 0 nodes (node [0]) cyclical broadcasting news other nodes to cancel the reception Interest and transmitted out
sense-2.0.1
- nRF24E1 sample sensor node code-nRF24E1 sensor node sample code
aa_3
- 学习掌握单总线数字式温度传感器 DS18B20的64位激光ROM码的读出方法。读DS18B20 64位ROM码命令（33h）允许主机直接读出从机的64位ROM代码，而无须执行搜索ROM 过程。如果该命令用于多节点系统，则必然发生数据冲突，因为每个从机设备都会响应该命令。64 位激光ROM 从高位到低位依次由8 位CRC、48 位列号和8 位家族代码(28H)组成。-learning and mastering digital single bus DS18B20 64 laser ROM cod
CANjiediantongxinchengxu
- 其中包括ＣＡＮ节点初始化程序，发送和接收程序-including CAN node initialization procedure, the sending and receiving procedures
LIN_2.0_CH LIN协议v2.0中文版，包括协议规范包
- LIN协议v2.0中文版，包括协议规范包、物理层规范、应用程序接口规范、节点能力语言规范以及配置语言规范-LIN protocol v2.0 Chinese, including the protocol specification package, the physical layer specification, the application interface specification, the node capacity and configuration language spec
Octopus
- Java编写的Linux下用来监控无线传感器网络节点的程序，使用了tinyOS-Written in Java under Linux to monitor wireless sensor network node, the use of the tinyOS
can_show_remote
- CAN总线上挂接两个节点，当其中一个节点（节点1）的按键按下时，除了自身的数码管1、2显示加一，还向节点2发送一个远程帧；节点2接收到远程帧后想总线发送一个数据帧，如果节点2的按键被按下时，除了自身的数码管1、2显示加一，还会向总线发送数据帧，使得节点2的数码管3、4显示与其保持一致。-CAN bus articulated two nodes, when one node (Node 1) of the button is depressed, in addition to its own d
W_WSN
- WSN节点的无线发射部分参考设计，设计加大的发射功率-WSN node wireless transmitter reference design, design to increase the transmitting power
SoilTemperatureMeasurement
- 基于NesC/TinyOS的无线传感器网络测量节点源码，平台：Crossbow IRIS，按用户指定时间间隔读取Decagon公司的EC5和EC-TM传感器信息-Based on NesC/TinyOS wireless sensor network node measurement source, platform: Crossbow IRIS, according to user-specified time interval to read Decagon s EC5 and EC-TM
GenericBase
- 无线网络传感器基站通用节点测试程序.包含基站接口和主模块程序.-Wireless network base station GM sensor node test procedure. Includes the base station interface and the main module procedures.
RF_HUB
- 用cypress的3721芯片做的无线中心结点c代码，接收外部结点来的数据。-Cypress chips used to do the 3721-node wireless Center, c code, receive outside data node.
MF_TEMP
- cypress cy3721做的外部无线结点。感知温度后将温度值反给中心结点。-The cypress cy3721 external wireless node. Perceived value of the temperature after the temperature to the central anti-node.
gpio-test
- 1、将makefile中的 CROSS =/usr/local/arm/2.95.3/bin/arm-linux- CFLAGS+=-I/usr/local/src/2.4.18-rmk7/include CFLAGS+=-I/usr/local/src/2.4.18-rmk7/include/linux CFLAGS+=-I/usr/local/arm/2.95.3/arm-linux/include 路径改为你宿主机上的。 2、#make，来编译驱动模块。 3、
node
- 无线传感器节点源代码，采集节点 avr/cc1-Source code for wireless sensor nodes, collecting node avr/cc1000
speak
- 无线传感器网络环境下，节点广播时的实验程序代码-Wireless sensor network environment, node broadcasting experimental code
node
- node code for wireless sensor networks
two-node-communication-cc2430
- 物联网必学芯片CC2430 实验例程：实现两个节点模块的通信 注意：开发环境应为 IAR Embedded Workbench-Things will learn experimental routine CC2430 chip: the communication module implements two node Note: the development environment should be IAR Embedded Workbench
node
- jennic radio module node , promiscuit mode IEEE802.15
The-gate-node
- 这是Neuron C编写的一个门节点，使用的开发环境是LonWorks-This is written in Neuron C a gate node, the development environment is LonWorks
node-to-node_FDMA
- 基于zigbee的点对多点无线通信FDMA，实现数据节点到节点的传输-Based on zigbee point to multipoint wireless communication FDMA, data node to node transmission