搜索资源列表
S2E-TI
- 嵌入式串口转以太网控制器，以下简称S2E21，是一款具有高效性能并集成了ARM Cortex-M3微处理器的串行至以太网控制器。该控制器的核心是高度集成的32位Stellaris LM3S6432 ARM Cortex-M3微处理器，具有50MHz性能和96K快速单周期片上闪存及32K SARAM内存，可高效处理网络流量。Stellaris系列微处理器采用LQFP-100 封装，并集成了片上10/100MB以太网MAC和PHY，从而能够最大限度的节省空间。-Embedded Serial to
C328R
- Header file to handle the C328R jpeg camera using atmel atmega88 uart.
gps-unit
- Some Routines to handle GPS Data in Pascal
shizhong
- 如果是用pc的串口传输数据就好办了，可以安装一个串口监视工具（如AccessPort）。电脑串口一般是2、3、5三根线通讯，2是txd，3是rxd，5是GND，但是电脑的逻辑电平与单片机的逻辑电平不同，具体看串口通信协议，网上很容易搜到。 IIC总线上的数据可以通过示波器查看，两个探头，一个连接clk，另一个连接sda，IIC通信时可以观察到传输的数据。 -If you are using pc' s serial port to transfer data much easier t
SET_top_box_video
- 详细讲述了如何处理数字电视机顶盒中的视频信号，很有参考价值。-Detail how to handle digital TV set-top boxes in the video signal, a good reference.
sd-card
- 该例程在开发板上实现了接入sd—card功能，并能初步处理卡上内容-The routine on the development board implements access sd-card functions, and can handle the initial content on the card
dtu
- 启动服务之后应该启动一个线程来轮询DTU数据，收到数据后直接处理，或放数据缓存，再由其他线程来处理用来定义宏电dtu的工作线程-After the start the service should start a thread to poll the DTU data, received data directly, or put the data cache, and then from the other thread to handle the electricity used to de
Singlechip-Key-Procedure
- 该文件是用AVR单片机控制工业电磁阀的按键程序，可实现设置开阀时间，关阀时间，开阀，关阀，手动自动切换等功能-the file contain the ketboard procedure based on AVR singlechip controller with the fuctions of setting the open time and close of the vavle, openning and closing the vavle and the switch between
QNX-character
- 一些QNX字符IO的说明，如何操作字符设备以及字符设备的共享库等等。-A descr iption about the IO character,like how to handle the IO device and related library.
yt
- 云台的控制及亚安云台的控制协议。 可做手柄键盘的参考。-PTZ control and Yaan PTZ control protocol. Do handle keyboard reference.
f51
- 51单片机上实现对PS2手柄的解析 解决单片机的无线连接-Analysis of PS2 handle 51 microcontroller
STM32_Bipolar-stepper-motor-drive
- STM32双极性步进电机驱动的源代码，完整的功能，库文件。 KEIL下运行-Main function: HAL generic update Fix flag clear procedure: use atomic write operation = instead of ready-modify-write operation |= or &= Fix on Timeout management, Timeout value set to 0 pas
xbee_remote
- 基于arduino智能车手柄控制程序，无线模块采用Xb-Arduino smart car based on the handle control procedures, the use of wireless module Xbee
SPI_of_MSP430F249
- SPI master talks to SPI slave using 3-wire mode. Incrementing data is sent by the master starting at 0x01. Received data is expected to be same as the previous transmission TXData = RXData-1. USCI RX ISR is used to handle communication with
UnoJoyArduinoSample
- ARDUINO实现游戏手柄的程序，四个方向控制，13个按钮控制(ARDUINO realize the game handle procedures, four direction control, 13 button control)